losetup

(8)

set up and control loop devices

Administration and privileged commands 20 optionsmount 2.41-5

Get info: losetup [loopdev] losetup -l [-a] losetup -j file [-o offset] Detach a loop device: losetup -d loopdev ... Detach all associated loop devices: losetup -D Set up a loop device: losetup [-o offset] [--sizelimit size] [--sector-size size] [--loop-ref name] [-Pr] [--show] -f|loopdev file Resize a loop device: losetup -c loopdev

Options

-a--all

Show the status of all loop devices. Note that not all information is accessible for non-root users. See also --list. The old output format (as printed without --list) is deprecated.

-D--detach-all

Detach all associated loop devices.

-f--findfile

Find the first unused loop device. If a file argument is present, use the found device as loop device. Otherwise, just print its name.

--show

Display the name of the assigned loop device if the -f option and a file argument are present.

-L--nooverlap

Check for conflicts between loop devices to avoid situation when the same backing file is shared between more loop devices. If the file is already used by another device then re-use the device rather than a new one. The option makes sense only with --find.

-j-o--associatedfile

Show the status of all loop devices associated with the given file.

-o--offsetoffset

The data start is moved offset bytes into the specified file or device. The offset may be followed by the multiplicative suffixes; see above.

--loop-refstring

Set reference string. The backwardly compatible default is to use the backing filename as a reference in loop setup ioctl (aka lo_file_name). This option can overwrite this default behavior and set the reference to the string. The reference may be used by udevd in /dev/loop/by-ref. Linux kernel does not use the reference at all, but it could be used by some old utils that cannot read the backing file from sysfs. The reference is readable only for the root user (see --output +REF) and it is restricted to 64 bytes.

--sizelimitsize

The data end is set to no more than size bytes after the data start. The size may be followed by the multiplicative suffixes; see above.

-b--sector-sizesize

Set the logical sector size of the loop device in bytes (since Linux 4.14). The option may be used when creating a new loop device as well as a stand-alone command to modify sector size of the already existing loop device.

-c--set-capacityloopdev

Force the loop driver to reread the size of the file associated with the specified loop device.

-P--partscan

Force the kernel to scan the partition table on a newly created loop device. Note that the partition table parsing depends on sector sizes. The default is sector size is 512 bytes, otherwise you need to use the option --sector-size together with --partscan.

-r--read-only

Set up a read-only loop device.

--direct-io

Enable or disable direct I/O for the backing file. The default is off. Specifying either --direct-io or --direct-io=on will enable it. But, --direct-io=off can be provided to explicitly turn it off.

-v--verbose

Verbose mode.

-l--list

If a loop device or the -a option is specified, print the default columns for either the specified loop device or all loop devices; the default is to print info about all devices. See also --output, --noheadings, --raw, and --json.

--output-all

Output all available columns.

-n--noheadings

Don’t print headings for --list output format.

--raw

Use the raw --list output format.

-J--json

Use JSON format for --list output.

DESCRIPTION

losetup is used to associate loop devices with regular files or block devices, to detach loop devices, and to query the status of a loop device. If only the loopdev argument is given, the status of the corresponding loop device is shown. If no option is given, all loop devices are shown.

Note that the old output format (i.e., losetup -a) with comma-delimited strings is deprecated in favour of the --list output format.

It’s possible to create more independent loop devices for the same backing file. This setup may be dangerous, can cause data loss, corruption and overwrites. Use --nooverlap with --find during setup to avoid this problem.

The loop device setup is not an atomic operation when used with --find, and losetup does not protect this operation by any lock. The number of attempts is internally restricted to a maximum of 16. It is recommended to use for example flock(1) to avoid a collision in heavily parallel use cases.

ENCRYPTION

Cryptoloop is no longer supported in favor of dm-crypt. For more details see cryptsetup(8).

EXIT STATUS

losetup returns 0 on success, nonzero on failure. When losetup displays the status of a loop device, it returns 1 if the device is not configured and 2 if an error occurred which prevented determining the status of the device.

NOTES

Since version 2.37 losetup uses LOOP_CONFIGURE ioctl to setup a new loop device by one ioctl call. The old versions use LOOP_SET_FD and LOOP_SET_STATUS64 ioctls to do the same.

ENVIRONMENT

LOOPDEV_DEBUG=all

enables debug output.

FILES

/dev/loop[0..N]

loop block devices

/dev/loop-control

loop control device

EXAMPLE

The following commands can be used as an example of using the loop device.

# dd if=/dev/zero of=~/file.img bs=1024k count=10
# losetup --find --show ~/file.img
/dev/loop0
# mkfs -t ext2 /dev/loop0
# mount /dev/loop0 /mnt
...
# umount /dev/loop0
# losetup --detach /dev/loop0

AUTHORS

Karel Zak kzak@redhat.com, based on the original version from Theodore Ts’o tytso@athena.mit.edu.

REPORTING BUGS

For bug reports, use the issue tracker https://github.com/util-linux/util-linux/issues.

AVAILABILITY

The losetup command is part of the util-linux package which can be downloaded from Linux Kernel Archive https://www.kernel.org/pub/linux/utils/util-linux/.